Sorry! You are trying to check out one of our items which is no longer available. Why not check out one of these alternate options?
Fuse Holder - 3AG-Type, High Quality
High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
Fuse Holder - for Fender®, 3AG-Type
High quality Fender® Style fuse holder replacement for guitar amplifiers.
- Fits ½" chassis hole diameter
- Mounted by Nut
Fuse Holder - 3AG-Type, Low Profile, Knob, Right Angle Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile bayonet style knob and reduced overall height. The connector at the end of the holder is right angled which reduces the internal depth as well. It is a similar style to fuse holders used on many Fender® amps. Mounting nut and rubber washer included.
Fuse Block - for 3AB and 3AG fuses, low profile
Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
Fuse Holder - Clip, GMA-Type, PCB Mount
Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.
Receptacle - AC with Fuse Holder, mates with S-W123 & S-W124
I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses
Fuse Holder - 3AG-Type, Low Profile, Slotted, Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.
Receptacle - IEC C14, Panel Mount, Fuse Holder, 10A, 250VAC
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. This receptacle features a built-in fuse holder for 5mm x 20mm fuses. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
Fuse Holder - 3AG-Type, Tweed Style, Solder Lug
Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Fuse Holder - for Marshall, ¼" Fuses
Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:
- Rated current: 10A
- Rated voltage: 250V AC
- Contact resistance: 2MΩ @ 250V DC or less
- Dialectric withstand: 1 minute @ 1500V AC
- Insulation resistance: 100MΩ or more @ 500V DC
Fuse - Slow-Blow, 250V, 3AG, 0.25" x 1.25"
The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.
Fuse - Slow-Blow, 250V, Miniature, GMD-type 5mm x 20mm
Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5