Integrated Circuits

µA741 single op amp in an 8-pin DIP package. The µA741 device is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation ensures stability without external components. A low-value potentiometer may be connected between the offset null inputs to null out the offset voltage. Features

• Short-Circuit Protection
• Offset-Voltage Null Capability
• Large Common-Mode and Differential Voltage Ranges
• No Frequency Compensation Required
• No Latch-Up

OPA2134 SoundPlus™ Audio dual op-amp with low distortion, low noise and precision. The OPA2134 are ultra-low distortion, low-noise operational amplifiers fully specified for audio applications. A true FET input stage is incorporated to provide superior sound quality and speed for exceptional audio performance. This, in combination with high output drive capability and excellent DC performance, allows for use in a wide variety of demanding applications. In addition, the OPA2134 has a wide output swing, to within 1 V of the rails, allowing increased headroom and making it ideal for use in any audio circuit. The OPA2134 SoundPlus™ audio operational amplifiers are easy to use and free from phase-inversion and the overload problems often found in common FET-input operational amplifiers. They can be operated from ±2.5-V to ±18-V power supplies.

LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features

• No Frequency Compensation Required
• Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• Low-Power Consumption
• 8-Lead TO-99 and 8-Lead PDIP
• No Latch Up When Input Common Mode Range is Exceeded

The AS3080E is Alfa’s version of the CA3080 IC. The AS3080E is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080E has differential input and a single-ended, push-pull, class A output. Amplifier bias
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.

NE5534 single op amp in an 8-pin DIP package. The NE5534 device is a high-performance operational amplifier combining excellent dc and ac characteristics. Some of the features include very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, and high slew rate. These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization of the frequency response for various applications can be obtained by use of an external compensation capacitor between COMP and COMP/BAL.

The XVive MN3009 is a drop-in replacement for the original Panasonic 256-stage MN3009 BBD chip used in many chorus, vibrato, and flanger pedals and effects. The MN3009 is a 256-stage BBD that boasts a wide dynamic range and low distortion. Its signal delay of up to 12.8 milliseconds makes it a perfect choice for vibrato and/or chorus effects in electronic musical instruments.

Dual Operational Amplifier. The NJM4558 (JRC4558) integrated circuit is a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip using an advanced epitaxial process. Combining the features of the NJM741 with the close parameter matching and tracking of a dual device on a monolithic chip results in unique performance characteristics. Excellent channel separation allows the use of the dual device in single NJM741 operational amplifier applications providing density. It is especially well suited for applications in differential-in, differential-out as well as in potentiometric amplifiers and where gain and phase matched channels are mandatory. Features:

• Operating Voltage (±4V~±18V)
• High Voltage Gain (100dB typ.)
• High Input Resistance (5MΩ typ.)
• Bipolar Technology

LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.

NJM4580L dual op amp from JRC in a SIP8 package. The NJM4580L is the same as the DIP NJM4580 (JRC4580) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4580 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, and it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools.

The NJM5532 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:

• Operating Voltage = ±3V~±22V
• Small Signal Bandwidth = 10MHz typ.
• Output Drive Capability = 600Ω,10Vrms typ.
• Input Noise Voltage = 5nV/√Hz typ.
• Power Bandwidth = 140kHz typ.
• Slew Rate = 8V/µs typ.
• Bipolar Technology

24LC32A/P EEPROM in an 8-pin DIP package commonly used in Spin FV-1 projects. The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced, low power applications such as personal communications or data acquisition. The 24LC32A also has a page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range make this device ideal for low-power/low-voltage, nonvolatile code and data applications.

LM318 single op amp in an 8-pin DIP package. The LM318 is a precision, fast operational amplifier designed for applications requiring wide bandwidth and high slew rate. They feature a factor-of-ten increase in speed over general-purpose devices without sacrificing dc performance. These operational amplifiers have internal unity-gain frequency compensation. This considerably simplifies their application because no external components are necessary for operation. However, unlike most internally compensated amplifiers, external frequency compensation may be added for optimum performance. For inverting applications, feed-forward compensation boosts the slew rate to over 150 V/µs and almost double the bandwidth. Overcompensation can be used with the amplifier for greater stability when maximum bandwidth is not needed. Further, a single capacitor can be added to reduce the settling time for 0.1% error band to under 1 µs.

LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.

TC7660S charge pump voltage converter in an 8 pin DIP package. The TC7660S device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and electromagnetic interference (EMI). Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10 kHz. Frequency is increased to 45 kHz when pin 1 is connected to V+.

LM833 dual op amp in an 8-pin dip package. The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier IC utilizes new circuit and processing techniques to deliver low noise, high speed and wide bandwidth without increasing external components or decreasing stability. The LM833 is internally compensated for all closed loop gains and is therefore optimized for all preamp and high level stages in PCM and HiFi systems. The LM833 is pin-for-pin compatible with industry standard dual operational amplifiers. Features

• Wide dynamic range: >140dB
• Low input noise voltage: 4.5nV/ √ ^Hz
• High slew rate: 7 V/μs (typ); 5V/μs (min)
• High gain bandwidth: 15MHz (typ); 10MHz (min)
• Wide power bandwidth: 120KHz
• Low distortion: 0.002%
• Low offset voltage: 0.3mV
• Large phase margin: 60°

Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.

OP07 precision op amp in an 8-pin DIP package.These devices offer low offset and long-term stability by means of a low-noise, chopperless, bipolar-input-transistor amplifier circuit. For most applications, external components are not required for offset nulling and frequency compensation. The true differential input, with a wide input-voltage range and outstanding common-mode rejection, provides maximum flexibility and performance in high-noise environments and in noninverting applications. Low bias currents and extremely high input impedance are maintained over the entire temperature range.

RC4558 dual op amp in an 8-pin DIP package. The RC4558 device is a dual general-purpose operational amplifier, with each half electrically similar to the µA741, except that offset null capability is not provided. The high common-mode input voltage range and the absence of latch-up make this amplifier ideal for voltage-follower applications. The device is short-circuit protected, and the internal frequency compensation ensures stability without external components. Features

• Continuous Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• No Frequency Compensation Required
• Low Power Consumption
• No Latch-Up
• Unity-Gain Bandwidth: 3 MHz Typ
• Gain and Phase Match Between Amplifiers
• Low Noise: 8 nV/√Hz Typ at 1 kHz

Applications

• DVD Recorders and Players
• Pro Audio Mixers

LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.

TL061 single op amp in an 8-pin DIP package. The JFET-input operational amplifiers of the TL06x series are designed as low-power versions of the TL08x series amplifiers. They feature high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents. The TL06x series features the same terminal assignments as the TL07x and TL08x series. Features

• Very Low Power Consumption
• Typical Supply Current: 200 µA (Per Amplifier)
• Wide Common-Mode and Differential Voltage Ranges
• Low Input Bias and Offset Currents
• Common-Mode Input Voltage Range Includes VCC+
• Output Short-Circuit Protection
• High Input Impedance: JFET-Input Stage
• Internal Frequency Compensation
• Latch-Up-Free Operation
• High Slew Rate: 3.5 V/µs Typical

The NJM4580D (JRC4580) is a dual opamp popularly used in many distortion pedals. This chip is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools. It is also suitable for the headphone amp at higher output current, and furthermore, it can be applied for the handy type set operational amplifier of general purpose in application of low voltage single supply type which is properly biased of the low voltage source. Features:

• Operating Voltage ±2V~±18V
• Low Input Noise Voltage 0.8µVrms typ.

LF356 single op amp in an 8-pin DIP package. The LFx5x devices are the first monolithic JFET input operational amplifiers to incorporate well-matched, high-voltage JFETs on the same chip with standard bipolar transistors (BI-FET™ Technology). These amplifiers feature low input bias and offset currents/low offset voltage and offset voltage drift, coupled with offset adjust, which does not degrade drift or common-mode rejection.

The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and thus their output DC levels) are independent of IABC.

NE5532 dual op amp in an 8-pin DIP package. The NE5532 device is a high-performance operational amplifier combining excellent DC and AC characteristics. They feature very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input-protection diodes, and output short-circuit protection. These operational amplifiers are compensated internally for unity-gain operation. These devices have specified maximum limits for equivalent input noise voltage. Features

• Equivalent Input Noise Voltage: 5 nV/√Hz Typ at 1 kHz
• Unity-Gain Bandwidth: 10 MHz Typ
• Common-Mode Rejection Ratio: 100 dB Typ
• High DC Voltage Gain: 100 V/mV Typ
• Peak-to-Peak Output Voltage Swing 26 V Typ With VCC± = ±15 V and RL = 600 Ω
• High Slew Rate: 9 V/μs Typ