New Products

Eddystone 26827PSLA enclosure with similar dimensions to the Hammond 1590D enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590D style builds.

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Aluminum alloy to BS1490, LM2M - supplied in natural finish.
• Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
• Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
• Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
• Countersunk lid holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

New old stock 2N404A PNP germanium transistors manufactured by Texas Instruments. These TI 2N404A feature gold plated leads. The 2N404A is used in many fuzz pedals along with other effects. The 2N404A is the same as the 2N404 but with a higher voltage rating. This transistor is in a TO-5 package with long leads commonly found on germanium transistors.

Pre-drilled wedge shaped pedal enclosure by Mod® Electronics. The shape of this folded steel enclosure is inspired by the original FZ-1 and FZ-1A Fuzz Tone enclosures but the predilled layout is inspired by the Octavio and the early Carlsbro fuzz. This provides a classic pedal design with a layout that is more compatible with modern pedalboards than the original Fuzz Tone layout. The layout is intended for two pots, two jacks, and a footswitch so many fuzz varieties can be built in this enclosure. The wedge shaped fuzz enclosure features a hinged bottom cover for easy access to the battery. The four screws that attach the bottom are included.

Pre-drilled vintage style pedal enclosure by Mod® Electronics. The shape of this folded steel enclosure is inspired by the original MK1 Tone Bender enclosures and is pre-drilled to match the original layout of the MK1 pedal. The layout is intended for two pots, two jacks, and a footswitch so many fuzz varieties can be built in this enclosure. The MK1 fuzz enclosure features a removable bottom door for easy access to the battery. All required screws and rubber feet are included.

CE Manufacturing USA Made Multi Section Can Capacitor. Reproduced To Exact Mallory Specs Using Original Mallory Machinery.

• 40/40/40/40uF 525VDC.
• FP / Twist Lock Style. Solder Tabs.
• -10%, +50% Tolerance, 55°C Temperature Rating.
• 1-⅜" Dia. X 3.6" H.

Zero ohm (0Ω) resistors in a carbon film axial package. These resistors are a similar size to most common 1/4W carbon film and metal film resistors. Zero ohm resistors are useful as pcb jumpers as well as point to point jumpers. These can also be useful for true bypass 3PDT wiring.

~1" (25mm) diameter x 1" (25.4mm) high rubber foot / recessed bumper with a steel insert. The 0.217” (5.5mm) mounting hole works well with a variety of screw sizes. Screws sold separately.

Premium quality latching 3PDT switches from DeMont / Guyatone. These made in Japan switches are designed specifically for audio signals. The Demont 3PDT has ultra-smooth switching action and has a very low actuation force. It uses gold plated solder cup terminals for solid connections with a professional look. Mounting hardware included.

Solder skillfully with Weller's 5 - 30 Variable Wattage Precision Soldering Iron Station. With its ergonomic molded pencil grip handle, on-board tip storage and cleaner, and integrated safety rest, it's the perfect high-quality and versatile soldering iron station for all your soldering needs. Features

• Integrated safety rest
• Power wattage up or down
• Quick tip change
• Compact design
• Optimal precision and control
• 750°F / 400°C

Replacement choke for the Fender® part numbers 125C1A, 022699, and 036468 as used in the Bandmaster, Dual Showman, Pro Reverb, Twin Reverb, Super Reverb, and others. This choke is rated 4H 90mA DC.

Output transformer upgrade for the Fender® part numbers 125A35A, 125A3A, and 022905 as used in the:

• Bronco (AA764, AB764, Blackface, Silverface)
• Champ (Tweed, 5C1, 5E1, 5F1, AA764, Blackface, Silverface, Vibro Blackface)
• Harvard (6G10)
• Princeton (Tweed, 5B2, 5C2, 5D2, 5E2, 5F2, 5F2A)

This upgraded transformer features both 4 ohm and 8 ohm taps on the secondary. The primary has two impedance options for lower voltage (5K) and higher voltage (8k) models.

Replacement choke for the Fender® part numbers 125C3A and 022707 as used in the Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb, 1964 Blackface 6G15 Reverb, and others. This choke is rated 4H 50mA DC.

Large 6.02” x 3.27” x 1.98” Hammond 1590P1 enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Power transformer replacement for the Fender® part numbers 125P1B, 022772, and 66079B. This transformer offers two different B+ options for lower voltage or higher voltage builds. This transformer is used in versions of the:

• Bronco
• Champ
• Princeton
• Princeton Reverb
• Vibro Champ

Features

• 275V or 325V (650/550 VCT) B+ options at 100mA
• Center tapped 6.3V filament at 2.25A
• 5V filament supply at 3A
• For 120V 60Hz primary
• Standard 2.5” x 2” mounting centers

Replacement reverb driver transformer for the Fender® part numbers 125A20B, 022921, and 037099. This is the standard reverb driver transformer used in most Fender amps that use a 12AT7 and transformer driven 4AB3C1B tank. Found in countless Fender® models including original and reissues of the following:

• Fender Princeton Reverb
• Fender Deluxe Reverb
• Fender Vibrolux Reverb
• Fender Pro Reverb
• Fender Super Reverb
• Fender Twin Reverb
• Fender Quad Reverb
• Fender Super Six Reverb
• Fender Vibrosonic
• Many others

Square 3.62” x 3.62” x 1.50” Hammond 1590Y enclosure. This enclosure is a stylish option for builds offering a similar amount of space as a 1950BB enclosure.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

U.S. made and true to vintage 1950s specifications. This lightweight (35 grams) wraparound bridge is made of aluminum to match the original 1950s version. High quality plating is used on all options. Each side is adjustable using the included hex set screws to dial in the intonation. Mounting studs sold separately. For a full set with all hardware included, please see P-GKLU-KLP1127N.

• 3.22 in. (82mm) stud spacing

Iss. 2 fuzz PCB made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This PCB is a recreation of the iss. 2 circuit board found in classic Fuzz Face pedals. The iss. 2 version uses NPN silicon transistors. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures. For the germanium iss. 1 version of this board, see P-PC-FUZZ-ISS1-BRN.

9V battery clip with a fiberboard frame. This high quality battery snap features tinned brass eyelets that secure the nickel-plated steel contacts to the fiberboard. Wires can be soldered directly to the eyelets allowing for custom length battery connections. This fiberboard style is similar to the 9V battery connectors in vintage electronics such as the Arbiter Fuzz Face.

1591T Series enclosure made of clear polycarbonate. The 1591B is a similar size to the 1590B diecast aluminum enclosures. Includes four cover screws and pre-installed brass inserts.

• Ideally suited for mounting printed circuit boards.
• Perfect for applications where parts, sensors or indicators need to be visible.
• Crystal Clear version is almost totally transparent.
• Integral card guides accept 1.5 mm (0.062”) P.C. cards.
• Lap joint construction provides protection against access of dust and splashing water.
• Designed to meet IP54.
• Molded from flame retardant, easy to machine, translucent polycarbonate (material carries a UL flammability rating of 94V-2).
• Lid is secured with M3 x 10 mm Phillips machine screws, threaded into integral brass bushings.

High quality chicken head knobs that resemble the style of knob found on the Zonk Machine II and Shatterbox fuzz pedals. The Zonk chicken head knob has a contoured center band with a textured finish. The outer dome has a shiny finish offering a visual contrast. Fits 0.25” (6.35mm) shafts with set screw and brass insert.

• Height: 0.75 in.
• Length: 1.065 in.
• Fits ¼" shaft with set screw

1591T Series enclosure made of clear polycarbonate. The 1591C is a similar size to the 1590N1 / 125B diecast aluminum enclosures. Includes four cover screws and pre-installed brass inserts.

• Ideally suited for mounting printed circuit boards.
• Perfect for applications where parts, sensors or indicators need to be visible.
• Crystal Clear version is almost totally transparent.
• Integral card guides accept 1.5 mm (0.062”) P.C. cards.
• Lap joint construction provides protection against access of dust and splashing water.
• Designed to meet IP54.
• Molded from flame retardant, easy to machine, translucent polycarbonate (material carries a UL flammability rating of 94V-2).
• Lid is secured with M3 x 10 mm Phillips machine screws, threaded into integral brass bushings.

CE Manufacturing USA Made Multi Section Can Capacitor. Reproduced To Exact Mallory Specs Using Original Mallory Machinery.

• 25/50/150uF 150VDC Electrolytic.
• FP / Twist Lock Style. Solder Tabs.
• -10%, +50% Tolerance, 55°C Temperature Rating.
• 1 ⅜"D X 3"H.

CE Manufacturing USA Made Multi Section Can Capacitor. Reproduced To Exact Mallory Specs Using Original Mallory Machinery.

• 47/47/47uF 350VDC Electrolytic.
• FP / Twist Lock Style. Solder Tabs.
• -10%, +50% Tolerance, 55°C Temperature Rating.
• 1 ⅜"D X 2.6"H.