Pedal Parts / DIY
OTA - AS3080E, Linearizing Diodes, Alfa, 8-Pin DIP
The AS3080E is Alfa’s version of the CA3080 IC. The AS3080E is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080E has differential input and a single-ended, push-pull, class A output. Amplifier bias
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.
Please Log In to view prices
OTA - LM13700, Dual, Linearizing Diodes and Buffers, 16-Pin DIP
The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and thus their output DC levels) are independent of IABC.
Please Log In to view prices
Op-Amp - OPA2134, Dual, High Performance Audio, 8-Pin DIP
OPA2134 SoundPlus™ Audio dual op-amp with low distortion, low noise and precision. The OPA2134 are ultra-low distortion, low-noise operational amplifiers fully specified for audio applications. A true FET input stage is incorporated to provide superior sound quality and speed for exceptional audio performance. This, in combination with high output drive capability and excellent DC performance, allows for use in a wide variety of demanding applications. In addition, the OPA2134 has a wide output swing, to within 1 V of the rails, allowing increased headroom and making it ideal for use in any audio circuit. The OPA2134 SoundPlus™ audio operational amplifiers are easy to use and free from phase-inversion and the overload problems often found in common FET-input operational amplifiers. They can be operated from ±2.5-V to ±18-V power supplies.
Please Log In to view prices
Op-Amp - NJM4580D, Dual, Audio, DIP 8
The NJM4580D (JRC4580) is a dual opamp popularly used in many distortion pedals. This chip is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools. It is also suitable for the headphone amp at higher output current, and furthermore, it can be applied for the handy type set operational amplifier of general purpose in application of low voltage single supply type which is properly biased of the low voltage source. Features:
- Operating Voltage ±2V~±18V
- Low Input Noise Voltage 0.8µVrms typ.
Please Log In to view prices
Integrated Circuit - Experimental Noize FXCore, DSP, Multi-Effect / Reverb
FXCore from Experimental Noize is a DSP designed for creating audio effects in pro-audio devices. FXCore can operate as a standalone device when paired with appropriate CODECs where it generates all necessary clocks or as part of a more complex system where it will lock to the word clock and bit clock provided by another part of the system.
FXCore can store up to 16 programs and their associated register preset values in its internal FLASH memory so no external program storage is required.
FXCore can store up to 16 programs and their associated register preset values in its internal FLASH memory so no external program storage is required.
Please Log In to view prices
IC Socket - Dual in-line package, 2.54mm Pitch, 7.62mm Spacing
IC component sockets for dual in-line package chips (DIP, PDIP, DIL, DIPP.) These sockets feature ladder style cases with tinned stamped and formed connections.
Please Log In to view prices
Op-Amp - LM741, Single, general purpose, 8-Pin DIP
LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.
Please Log In to view prices
Integrated Circuit - Xvive, MN3007, BBD, 1024 Stage
The XVive MN3007 is a drop-in replacement for the original Panasonic 1024-stage MN3007 BBD chip used in many chorus, vibrato, and flanger pedals and effects. The MN3007 is a 1024-stage, low-noise, long-delay BBD that provides a signal delay of up to 51.2 milliseconds. Due to its long delay times, the MN3007 is especially suitable for reverb effects in electronic musical instruments and PA equipment.
Please Log In to view prices
Op-Amp - LF353, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.
Please Log In to view prices
Op-Amp - TL082, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.
Please Log In to view prices
Op-Amp - TL062, Dual, Low-Power, JFET Input, 8-Pin DIP
Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.
Please Log In to view prices
Integrated Circuit - PT2399, Echo / Delay
PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.
Please Log In to view prices
Audio Power Amplifier - LM386N-1 / 4, Low Voltage
LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.
Please Log In to view prices
Op-Amp - TL074, Quad, Low-Noise, JFET Input, 14-Pin DIP
Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:
- Wide common-mode and differential voltage range
- Low input bias and offset current
- Low noise en = 15 nV/HZ
- Output short-circuit protection
- High input impedance JFET input stage
- Low harmonic distortion: 0.01%
- Internal frequency compensation
- Latch up free operation
- High slew rate: 16 V/us (typical)
Please Log In to view prices
Op-Amp - TL072, Dual, Low-Noise, JFET Input, 8-Pin DIP
The TL072 is a high speed JFET input dual operational amplifier incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
Please Log In to view prices
Op-Amp - NJM5532, Dual, Low-Noise, 8-Pin DIP
The NJM5532 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:
- Operating Voltage = ±3V~±22V
- Small Signal Bandwidth = 10MHz typ.
- Output Drive Capability = 600Ω,10Vrms typ.
- Input Noise Voltage = 5nV/√Hz typ.
- Power Bandwidth = 140kHz typ.
- Slew Rate = 8V/µs typ.
- Bipolar Technology
Please Log In to view prices
Op-Amp - M5201, Dual, With Switch, 8-Pin DIP
The NJM2120 is a dual operational amplifier of 2-INPUT and 1-OUTPUT with analog switch. The NJM2120 can be used as analog switch under the condition of GV=0dB, as Switch + Amp in order that each gain (A or B) can be adjusted independently. Each amplifier of the NJM2120 has the same electrical characteristics as the NJM4558. The NJM2120 is suitable for audio, video, electrical musical instrument, etc.
Please Log In to view prices
Op-Amp - BA4560, Dual, General Purpose, 8-Pin DIP
The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.
Please Log In to view prices
Op-Amp - LM833, Dual, Low Distortion, Audio, 8-Pin DIP
LM833 dual op amp in an 8-pin dip package. The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier IC utilizes new circuit and processing techniques to deliver low noise, high speed and wide bandwidth without increasing external components or decreasing stability. The LM833 is internally compensated for all closed loop gains and is therefore optimized for all preamp and high level stages in PCM and HiFi systems. The LM833 is pin-for-pin compatible with industry standard dual operational amplifiers. Features
- Wide dynamic range: >140dB
- Low input noise voltage: 4.5nV/ √ ^Hz
- High slew rate: 7 V/μs (typ); 5V/μs (min)
- High gain bandwidth: 15MHz (typ); 10MHz (min)
- Wide power bandwidth: 120KHz
- Low distortion: 0.002%
- Low offset voltage: 0.3mV
- Large phase margin: 60°
Please Log In to view prices
Op-Amp - LM1458, Dual, 8-Pin DIP package
LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features
- No Frequency Compensation Required
- Short-Circuit Protection
- Wide Common-Mode and Differential Voltage Ranges
- Low-Power Consumption
- 8-Lead TO-99 and 8-Lead PDIP
- No Latch Up When Input Common Mode Range is Exceeded
Please Log In to view prices
Op-Amp - LF356, Single, High Slew Rate, 8-Pin DIP
LF356 single op amp in an 8-pin DIP package. The LFx5x devices are the first monolithic JFET input operational amplifiers to incorporate well-matched, high-voltage JFETs on the same chip with standard bipolar transistors (BI-FET™ Technology). These amplifiers feature low input bias and offset currents/low offset voltage and offset voltage drift, coupled with offset adjust, which does not degrade drift or common-mode rejection.
Please Log In to view prices
Op-Amp - µA741, Single, Offset Null, 8-Pin DIP
µA741 single op amp in an 8-pin DIP package. The µA741 device is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation ensures stability without external components. A low-value potentiometer may be connected between the offset null inputs to null out the offset voltage. Features
- Short-Circuit Protection
- Offset-Voltage Null Capability
- Large Common-Mode and Differential Voltage Ranges
- No Frequency Compensation Required
- No Latch-Up
Please Log In to view prices
Op-Amp - TLC274, Quad, Precision, LinCMOS, 14-Pin DIP
TLC274 quad op amp in a 14-pin DIP package. The TLC274 quad operational amplifier combines a wide range of input offset voltage grades with low offset voltage drift, high input impedance, low noise, and speeds approaching that of general-purpose BiFET devices. These devices use Texas Instruments silicon- gate LinCMOSTM technology, which provides offset voltage stability far exceeding the stability available with conventional metal-gate processes. The extremely high input impedance, low bias currents, and high slew rates make these cost-effective devices ideal for applications which have previously been reserved for BiFET and NFET products.
Please Log In to view prices
Op-Amp - TL084, Quad, Wide Bandwidth, JFET-input, 14-Pin DIP
TL084 quad op amp in a 14-pin DIP package. These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage ( BI-FET II™ technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.
Please Log In to view prices