Pedal Parts / DIY

PCB for converting SMD TQFP-64 packages to through hole DIP-64 footprints with 0.9" width (wide DIP). Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

Solid tinned copper bus wire. Great for point to point builds, guitar electronics wiring, or any situation where insulated wire is not required. 105°C temperature rating, 600V. Sold by the foot. For 100ft spools, please see S-W428X.

Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. Made in China.

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets. 7 lugs, first and seventh lug common.

Two rows of 8 U-style terminals (16 total) on a black board. This U-style terminal strip is extra dense with 6.35mm terminal spacing allowing for even more densely populated point-to-point builds. The boards are 0.063” thick.

Durable nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features

• Approved for outdoor use.
• UL Listed 6.6 nylon.
• Locks tightly - Won’t stretch or slide.
• Temperature range from 40° to 180°F.

Pure Tone has developed a high quality 1/4" three pole (stereo) jack using a new patented design that improves upon and offers a more reliable connection than standard 1/4" jacks. The Pure Tone design features two springs for both the tip connection, a spring for the ring, and an additional spring for the shield connection. These help to secure the plug into place and create a greater surface area connection at contact points to improve stability and signal integrity. These jacks also increase the current capability of 1/4" connections.

High quality black plastic chickenhead knob. 1-1/4" in length. Push-on for split knurled shaft.

MKII fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Tone Bender Professional MKII pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKII boards were cut from stripboard, this board follows the same format but is completely ready for soldering with precut traces and drilled mounting holes. The build style is very straightforward on the Mk2. It is a standard stripboard build and follows a very linear circuit path across the board.The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. For modern versions of this board, see P-PC-BEND-MKII-X.

The BC557 is a silicon general purpose PNP transistor in a TO-92 package. The BC557’s typical applications include signal processing, amplification, and switching.

High quality latching relays from the Panasonic TQ series. These 5 volt relays are commonly used in pedals for true bypass switching. Relay switching can allow for a variety of options on pedal builds. Different footswitch modes can be obtained using the same momentary footswitch. Stereo switching using a standard footswitch is another possible option.
Features:

• Compact low profile size
• Standard DIL spacing for easy PCB use and breadboard compatibility
• Latching
• Single Coil
• 5V Coil Voltage

For a non-latching version, please see P-RP-TQ2-5V.

Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. This lightweight desoldering pump has an anodized aluminium body to assure durability and features a plunger safety shield, short-stroke plunger and a no-clog automatic tip cleaner. Replace tip with S-T7875B. Made in Taiwan.

This vintage knob design has been used on numerous boutique pedals. These classy knurled pointer knobs feature a slotted set screw, and fit ¼" solid shaft potentiometers. These are a close match to the Davies 1400.

• Height: 0.43 in.
• Length: 0.825 in.
• Fits ¼" shaft with set screw

High-quality solder lug linear taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.

• Solder lug / panel mount
• Linear taper
• +/- 10% tolerance
• ¼” (6.35mm) solid shaft
• Machine-pressed dust seal
• High quality wiper material
• Low residual resistance

For audio taper solder lug pots see R-VGORVA-AX-SL. For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC.

A great digital reverb sound that easily replaces a spring reverberation unit. Stereo outputs may be summed for mono operation. Simple interface requires only input, output, +5V, and ground.

Phenolic skirted knobs with a set screw and brass insert. These unique knobs closely match the RCA style of knobs used on vintage test equipment, radios, studio consoles and other equipment. They are sometimes referred to as fester knobs. The RCA style knobs feature an inlay indicator line. Fits ¼” (6.35mm) pot shafts. 22mm Skirt:

• Height: 0.495in. (12.6 mm)
• Diameter: 0.875 in. (22 mm)
• Fits ¼" shaft with set screw

26mm Skirt:

• Height: 0.656 in. (16.7 mm)
• Diameter: 1.02 in. (26 mm)
• Fits ¼" shaft with set screw

33mm Skirt:

• Height: 0.792 in. (20.1 mm)
• Diameter: 1.293 in. (33 mm)
• Fits ¼" shaft with set screw

40mm Skirt:

• Height: 0.865 in. (22 mm)
• Diameter: 1.568 in. (40 mm)
• Fits ¼" shaft with set screw

Dust cover for smaller low profile DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Measures 4.77" x 2.58" x 1.41". Add 0.16" to enclosure depth for lid.

High quality panel mount potentiometers from Omeg. These made-in-UK pots match the vintage Radiohm pots found in many vintage fuzz effects such as the Fuzz Face and Tonebender pedals and are a favorite for vintage style builds. They feature a high quality conductive polymer track that offers improved stability and extended life. Includes mounting nut and lock washer. Features

• ⅜ in. Bushing
• Panel Mount
• Linear Taper
• Made in UK
• Life Expectancy of >20,000 cycles (tested at 30 times per minute)
• Conductive polymer (plastic) track (over twice the life of carbon tracks)
• Rotation angle: 300° ±5°
• Tolerance on Rated Resistance: ± 20%

High-quality USA made knobs from Rogan Corp. These medium pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm D-shafts.

• Height: 0.68 in.
• Diameter: 0.50 in.
• Fits 6mm D Shafts
• Indicator on round side of D-shaft

For a T18 knurled version of this knob, see P-K272P-W. A variety of different sizes are available from the PT Series.

The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.

9 volt battery clip with 5 3/4" red and black wire lengths. Simple construction and perfect for use in effects pedals. Package of three.

The CD4070B contains four independent Exclusive-OR gates. The CD4070B provides the system designer with a means for direct implementation of the Exclusive-OR functions, respectively. Features:

• High-Voltage Types (20V Rating)
• CD4070B - Quad Exclusive-OR Gate
• Medium Speed Operation
• tPHL, tPLH = 65ns (Typ) at VDD = 10V, CL = 50pF
• 100% Tested for Quiescent Current at 20V
• Standardized Symmetrical Output Characteristics
• 5V, 10V and 15V Parametric Ratings
• Maximum Input Current of 1µA at 18V Over Full Package Temperature Range
• 100nA at 18V and 25°C
• Noise Margin (Over Full Package Temperature Range)
• 1V at VDD = 5V, 2V at VDD = 10V, 2.5V at VDD = 15V
• Meets All Requirements of JEDEC Standard No.