Tools

Cloth - Shop Towels, Super Absorbant, Disposable, 55 Sheets
Strong, absorbent towels for auto and machine shops. Works like cloth for your tough jobs. Absorbs grease and oil, even when wet. Fits any standard paper towel dispenser. 11” x 9" sheets.
Please Log In to view prices
StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes
ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
Please Log In to view prices
Adhesive Softener - Bob Smith Industries, Un-Cure
Un-Cure™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of Un-Cure™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastic parts with a razor saw is usually the best option. Works Well On:
  • Cyanoacrylates
  • Super Glues

Directions: Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water.
Please Log In to view prices
Jumper Test Lead Set - Clip 35mm, Total Length 24", 22AWG
Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green
package of 10
Please Log In to view prices
Marker - permanent paint, Black, Medium Tip
Medium tip paint marker. The black paint marker is suitable for both indoor and outdoor use. The oil-based paint leaves permanent marks.
Please Log In to view prices
Adhesive Remover - Bob Smith Industries, Insta-Clean
Insta-Clean™ is ideal for removing price stickers and their adhesive residue. Insta-Clean™ will also remove scuff marks that regular household cleaners won't touch. Works on all surfaces, including: glass, cardboard, plastic, fiberglass and everything else. Uses
  • Stickers
  • Sticker Residue
  • Residue on Glass
  • Residue on Fiberglass

Directions: Spray directly onto the sticker to be removed. Let stand for 1 to 5 minutes and then peel off sticker and wipe clean.
Please Log In to view prices
Allen wrenches - set of three sizes
Allen wrench set of three: 2.5mm, 3mm, 4mm
package of 3
Please Log In to view prices
StripBoard - Single Sided, 6.14” x 3.15”, Vintage Spacing, Black
Black stripboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has 40 x 20 holes (20 strips). Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm FR4 glass-epoxy circuit board
  • HASL coated strips
  • 40 x 20 holes (20 strips)
  • 6.14” x 3.15”

Looking for projects? See our Wide Stripboard projects in our Pedal Layouts & Build Guides section for ideas.
Please Log In to view prices
Nozzle - Angled, For Hot Air Station
Angled nozzle attachments for the Atten ST-862D hot air station. These attachments are a great accessory allowing for a more relaxed grip and better control. Sold individually.
Please Log In to view prices
Fret Press Inserts - for Pressing Frets, Multiple Radiuses
Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.
Please Log In to view prices
Solder wick - GC Braid, multiple sizes
5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.
Please Log In to view prices
PadBoard - Double Sided, Plated Holes, 3.94” x 3.15”, Mounting Holes
The PadBoard-2 prototyping circuit board has a general purpose pad-per-hole pattern which is good for analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. Features
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 31 x 39 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size2 = 100 x 80mm (3.94 x 3.15in), 1/16" thick (1.6mm)
Please Log In to view prices
ProtoBoard - Fits 1590BB, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590BB die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590BB enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190). Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 4 mounting holes.
  • PCB Size 3.20 x 4.25 in (81.3 x 108.0 mm)
Please Log In to view prices
Center Punch - Spring Loaded, Adjustable Force
Spring loaded center punch with an adjustable force for aligning pilot holes when drilling into materials. The large handle makes the push-to-strike action simple and accurate. Rotating the red handle adjusts the force amount.
Please Log In to view prices
Tool - Precision Devices, Lead Former, Various Sizes
High quality, made in USA lead formers. These are great tools for bending component leads to fit various footprints. The radiused ends provide a right angle bend that does not stress the metal lead. These lead formers are made of high impact ABS plastic.
Please Log In to view prices
Metal Stamp Set - 0-9 Digits, 0.125” Numeral Height
Metal stamp set with nine stamps for the numbers 0 through 9. The 6 stamp is also used for 9. The height of a stamped numeral is 0.125”. These stamps mark single characters by indenting the mark into the surface of a material. The process is simple, requiring only a hammer to strike the stamp onto the material. This stamp set is a great tool for adding control labels to projects such as pedal enclosures.
Please Log In to view prices
Knife - Scraper tool, Retractable Blade
High Quality retractable scraper blade. House in a small but comfortably sized handle, the blade makes scraping a simple task.
  • Scrape paint off, clean glass.
  • Retractable locking blade.
  • Includes 1 single-edge blade.
Please Log In to view prices
Desoldering Pump - Atten, AT-E33A, Solder Removal Tool
Atten AT-E33A heavy duty desoldering pump. This pump’s design provides a high vacuum force especially helpful for clearing circuit boards in rework jobs and field repair. Features
  • Piston with double oil seals
  • Handle delivers comfortable grip and non-slip function.
  • Compact size
  • Anti-rust spring
  • Built-in tip for easy replacement
  • Quick and easy cleaning
Please Log In to view prices
Tape - Painter’s, Outdoor, Blue, 1⁄2" x 60 yds
Blue outdoors painter's tape. Resists direct sunlight. Holds up to 14 days with clean removal. Recommended for detailed paint jobs.
Please Log In to view prices
Storage Box - for electronic components
This electronic component storage box works great for storing caps, pots, resistors and other electronic components. Made of plastic.
Please Log In to view prices
Soldering Iron Tip - Weller, narrow screwdriver type, ST Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
Please Log In to view prices
Soldering Iron Tip - Weller, hollow core, single flat / sloped type, ET Series
Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
Please Log In to view prices
Soldering iron tip - Weller, hollow core, 1.6mm, narrow screwdriver, ET Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
Please Log In to view prices
Soldering iron tip - Weller, conical, for WTCPT
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Conical Tip for TC201 Series Iron
  • PTP7 - 0.79mm / 0.031" diameter conical tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
Please Log In to view prices