Transformers & Chokes

Transformer - Hammond, Output, replacement for Marshall
  • Replacements for Marshall Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Please Log In to view prices
Transformer - Hammond, Guitar Amplifier, replacement for Marshall
  • Replacements for Marshall amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Please Log In to view prices
Transformer - Power, 120V primary, 140/28/10.5 V secondary
  • Primary Voltage: 120 V
  • Secondary 1: 140 V @ 100 mA
  • Secondary 2: 28 V @ 20 mA
  • Secondary 3: 10.5 V @ 2 A

Primary voltage = black wires Secondary 1 = Red wires Secondary 2 = Yellow wires Secondary 3 = Green wires
Please Log In to view prices
Transformer - Hammond, Universal Push-Pull
  • Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
  • Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
  • Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
  • Tables provided with transformer listing 90 pre-calculated impedance ratios.
Please Log In to view prices
Transformer - Hammond, Tube Output, Push-Pull
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Please Log In to view prices
Transformer - Hammond, Plate & Filament or Bias, 6.3 V auxiliary
  • Primary 115 VAC, 60 Hz.
  • Designed for small power or bias supplies, test equipment, preamps etc.
  • Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
  • Economical , two hole, channel bracket, chassis mount.
  • Minimum 5" long leads.
  • Convenient 6.3 filament/auxiliary winding.
Please Log In to view prices
Filter Choke - Hammond, D.C. choke, Enclosed
  • Enclosed, 4-hole mount chokes
  • Tolerance of 15% on both inductance & resistance.
  • Inductances measured at rated D.C. current.
  • Minimum 8" long leads.
  • Units will exhibit less inductance at slightly higher currents or more at lower currents.
  • Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
  • For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
  • Operating temperature range is -40C to 85C
Please Log In to view prices
Transformer - Fender®, Power, Hot Rod Deluxe
Fender Original Hot Rod Deluxe Power Transformer. Equivalent to #036958.



Specifications



Primary
120 VAC @ 60 Hz (Black - White)


Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC


Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC


Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC


Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Please Log In to view prices
Transformer - Output, 15W, 8kΩ CT Primary, for Fender® Deluxe 5E3
Paper bobbin output transformer replacement for the Fender® part number 50246 as used in the 5E3 Deluxe Amp. This transformer has an 8kΩ center tapped primary and an 8Ω secondary. Features
  • Paper Bobbin
  • Vintage Style Color Code
  • 8kΩ Center Tapped Primary
  • 8Ω Secondary
  • Standard 3.125” Mounting Centers
Please Log In to view prices
Transformer - Fender®, Reverb, for Pro Reverb
Original Fender® reverb driver for Pro Reverb. Replacement for #037099. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
See P-TGR-001 for a generic Fender® style reverb driver.
Please Log In to view prices
Transformer - Hammond, Low Voltage / Filament, Open, 12.6 VCT
  • Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 12.6V center tapped secondary
Please Log In to view prices
Transformer - Fender®, Power, Blues Junior, 15 W
Fender Original Blues Junior Power Transformer. Equivalent to #049967.
Please Log In to view prices
Switch - Rotary Impedance Selector, for Hammond 1600A series
Includes: 3 pole, 3 position rotary switch (3P3T), 1/4" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
Please Log In to view prices
Transformer - Hammond, Tube Output, Easy Wire Secondary
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Please Log In to view prices
Transformer - Hammond, Low Voltage / Filament, Open, 12 VCT
Open style, chassis mount transformers with a 115V 60Hz primary and a 12V center tapped secondary.
Please Log In to view prices
Transformer - Hammond, Low Voltage / Filament, Open, 2.5 VCT
  • Open style, chassis mount transformers with a 115V 60Hz primary and a 2.5V center tapped secondary.
Please Log In to view prices
Transformer - Marshall Replacement, Output, 100 W
Great for upgrading later issue Marshall™ amps. Gives great classic sound.
Good replacement for JMP and JCM 800s. for EL34!
Please Log In to view prices
Transformer - Fender, Power, for Deluxe Reverb 120V
Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary
Please Log In to view prices
Transformer - Power, 120V Primary, 330V / 6.3VCT / 5V Secondary, for Fender® Deluxe 5E3
Power transformer replacement for the Fender® part number 64526 as used in the 5E3 Deluxe Amp. This transformer accounts for modern mains voltage and will provide a B+ voltage of ~370VDC with 120VAC on the primary in a standard 5E3 build paired with the P-TGO-002 output transformer. This upgraded transformer also features a center tap on the 6.3V filament. Features
  • Provides vintage correct DC voltages in stock 5E3 builds
  • 330V (660 VCT) B+ at 120mA
  • Center tapped 6.3V filament at 2A
  • 5V filament supply at 2A
  • For 120V 60Hz primary
  • Standard 2.8125" x 2.25” mounting centers
Please Log In to view prices
Transformer - Hammond, Low Voltage / Filament, Open, 5 VCT
  • Open style, chassis mount transformers with a 115V 60Hz primary and a 5V center tapped secondary.
Please Log In to view prices
Transformer - Marshall, Output, 100 W, for JCM900
Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.
For a Hammond option, see P-T1750P.
Please Log In to view prices
Transformer - Hammond, Plate & Filament
  • Universal primary with taps for 100, 120, 220 or 240 VAC, 50 / 60 Hz. (Except the 260A6 which is 117V, 50/60 Hz only)
  • Designed for preamps, low power amps, general replacement, test equipment, etc.
  • Economical, open frame, chassis mount - two hole (.187 dia. = G) channel bracket (figure #1) or four hole mounting (figure #2).
  • Units include a Faraday shield between the primary and secondary windings. Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries.
  • Minimum 5" long leads.
  • For more selection check out our P-T300-X series of universal plate & filament transformers.
Please Log In to view prices
Transformer - Hammond, Guitar Amplifier, replacement for Fender, 120 V upgrade
  • Designed for drop in replacement of original units. Upgraded units with variable voltage.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • See P-T290-FENDER-120 for 120 V basic transformers, P-T290-FENDER-240 for 240 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.
Please Log In to view prices
Transformer - Fender® Replacement, Output, 50 W, 4 Ohm
Replacement for Bassman heads. Equivalent to #125A13A & #022871.
Please Log In to view prices